Skip to main content Skip to search Skip to main navigation

Free gifts for our shop launch

Offer details

€39.00 left until the free consumable

Accounts and orders from the old shop have been imported. Please set a new password via “Forgot password”.

Product information "Tool for jeans buttons 1/4" - 20 UNC"

This tool sets jeans buttons in the selected size. Two versions are available: closed for jeans buttons with a smooth outer cap and with hole for jeans buttons with an outer cap that has a hole. The tool with hole has a shoulder so that the cap with hole stays guided during pressing.

The upper tool part has a 1/4"-20 UNC thread and therefore fits all Getmore Crafts presses. The lower tool part sits in the 12 mm receptacle. Cap and counterpart are joined in a single pressing operation.

The size corresponds to the diameter of the outer cap. 11 mm is available closed only. 14, 17 and 20 mm are each available closed and with hole.

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Which size do I need?
The tool size corresponds to the diameter of the jeans button outer cap. For a 17 mm jeans button, choose a 17 mm tool.
What does With hole mean?
No is the closed tool without shoulder, for jeans buttons with a smooth outer cap. Yes is the tool with shoulder, for jeans buttons with an outer cap that has a hole.
Is 11 mm also available with hole?
No. In this listing, 11 mm is available closed only. 14, 17 and 20 mm are available closed and with hole.
Does the tool fit my Getmore Crafts press?
Yes. The upper tool part has a 1/4"-20 UNC thread, and the lower tool part is designed for the 12 mm receptacle. It therefore fits all Getmore Crafts presses.
Do I need to pre-punch the fabric?
No. Separate pre-punching is not required. The pin of the jeans button pierces the fabric during the pressing operation.
Are the upper and lower parts included?
Yes. You receive the upper and the lower tool part in the selected size and version.
What do I need to bear in mind with the spring impact press?
Tighten the upper tool part firmly with suitable pliers and check its fit regularly so that the thread does not loosen.

Size

  • 11 mm, 14 mm, 17 mm, 20 mm: The tool size corresponds to the diameter of the jeans button outer cap.
  • 11 mm is available closed only. 14, 17 and 20 mm are available closed and with hole.

With hole

  • No: Closed tool without shoulder, for jeans buttons with a smooth, closed outer cap.
  • Yes: Tool with shoulder, for jeans buttons with an outer cap that has a hole. The shoulder guides the open cap and does not flatten the hole.

Application steps

  • Choose the size and version to match the outer cap: closed for a smooth cap, with hole for a cap with a hole.
  • Screw the upper tool part fully into the press and insert the lower tool part into the 12 mm receptacle.
  • Place the outer cap in the tool part intended for it and the counterpart in the other.
  • Place the fabric in between, align the parts and press the jeans button in a single pressing operation.

Notes on use

  • Check the upper tool part regularly for a firm fit and retighten the thread if necessary.
  • On the spring impact press, the upper tool part should be tightened firmly with suitable pliers.
  • Separate pre-punching is not required. The pin of the jeans button pierces the fabric during the pressing operation.
  • The tool is designed for use in a press.

With Getmore Crafts products

With products from other manufacturers

  • Only usable with presses that have a 1/4"-20 UNC upper thread and a matching 12 mm receptacle at the bottom.
  • This listing is not suitable for presses with M6 or M8 thread. Separate tool variants are available for those.
  • There is no binding approval for jeans buttons from other manufacturers. What matters is the cap diameter and whether the outer cap is closed or has a hole.

Your package contains:

  • 1 upper tool part in the selected size and version
  • 1 lower tool part in the selected size and version

Not included:

Technical details

MaterialAlloy steel
Surface treatmentnickel-plated
Thread upper tool part1/4" - 20 UNC
Diameter lower tool part12 mm
Tool design2-part
Suitable forJeans buttons, closed outer cap and outer cap with hole
Available sizes11 mm (closed only); 14 mm; 17 mm; 20 mm
With hole versionNo = closed, without shoulder; Yes = with shoulder for cap with hole
Pre-punching requiredno
Suitable pressesTEP-2, spindle press, toggle press, spring impact press

Same workshop, new name

Welcome to our new shop

getmore-shop Getmore Crafts

We used to be getmore-shop. Now we are Getmore Crafts — same tools, same great service.

We’re celebrating the opening

Our new shop is open!

getmore-shop.com Getmore Crafts

We used to be getmore-shop.com — today we celebrate Getmore Crafts with free gifts on your order.

  • From €39 a consumable as a gift
  • From €79 a tool as an extra gift
Offer details

Accounts and orders from the old shop have been imported. Please set a new password via “Forgot password”.