Manufacturer / responsible person
Axel Gnann
Freiburgerstr. 9/1, 79312 Emmendingen, GermanyFor product safety questions and GPSR-related notices, please contact:
Product information "Hole Punch Tool Thread: 1/4" - 20 UNC"
This hole punch tool is designed for punching round holes in leather, faux leather, felt and cardboard. The selected tool size always corresponds directly to the resulting hole diameter.
The upper tool part is screwed in with 1/4\" - 20 UNC into a suitable press. The lower brass anvil sits in the 12 mm holder, protects the tool during punching and is part of the two-part hole punch system.
Login
1 - 10 of 16 reviews
11 May 2026 08:47
5 Sterne
Muy bien
26 February 2026 12:45
Bestens!
Funktioniert einwandfrei und ist deutlich angenehmer, als der Einsatz von Hand-Locheisen und Hammer :-)
26 January 2026 15:15
Sehr gut und präzise, tolle Qualität
Sehr gut und präzise, tolle Qualität, die Löcher fransen NICHT aus, sondern sind exakt wie es gewollt ist für die Weiterverarbeitung mit Ösen.
Hier kaufe ich sehr gerne ein, da der Service obendrein auch noch SEHR GUT ist
30 October 2024 07:19
perfekt
Die Bestellung hatte ich am nächsten Tag schon im Briefkasten . Wie immer ist es eine gut funktionierende Qualität . Werde immer wieder dort bestellen
24 April 2024 09:03
*****
Das Produkt leistet hervorragende Arbeit. Es locht jeden Stoff.
Sehr guter und kompetenter Geschäftspartner. Jederzeit gerne wieder.
12 December 2023 06:02
Ein sehr gutes Produkt
Wir verwenden die Locheisen hauptsächlich für Leder, in einer Federlochstanze in den Dimensionen von 2,5mm bis 14mm und natürlich verschleißen diese mit der Zeit, aber die Stanzungen sind sauber und die Standzeit ist ok.
19 May 2023 08:15
Bueno
Bien
22 March 2023 17:46
non fora bene il feltro
non buona non fora bene il tessuto bisogna completare il taglio con una forbice
15 September 2022 06:26
sehr gutes Produkt, schnelle Lieferung!
Wir sind sehr zufrieden mit den Getmore Produkten im Allgemeinen! Schnelle und zuverlässige Lieferung! Immer wieder gerne.
19 August 2022 20:58
Not great for Biothane
Might work better for leather to be fair, but it's not sharp enough for cleanly punching through Biothane.
What size do I need for my hole punch tool?
The tool size always corresponds directly to the resulting hole diameter. For a 3 mm hole, choose a 3 mm hole punch tool.
Which materials can I process with this hole punch tool?
The tool is intended for leather, faux leather, felt and cardboard. Paper cuts poorly with it, and no reliable approval for fabric is provided in this listing.
Does this hole punch tool fit my Getmore Crafts press?
Yes. The upper tool part has a 1/4" - 20 UNC thread, and the lower anvil is designed for the 12 mm holder. This makes the tool compatible with all Getmore Crafts presses.
Can I use it to prepare holes for eyelets, snap fasteners or hollow rivets?
Yes. For standard eyelets, choose the hole size to match the inner diameter of the eyelet. For our snap fastener and hollow rivet applications, a 2.5 mm hole is used.
Is the brass anvil included in the delivery?
Yes. The hole punch tool consists of an upper tool part and a lower brass anvil.
Can I also use the hole punch tool with a hammer?
That is not recommended. This tool is designed for use in a suitable press.
What should I note with the spring-strike press?
Tighten the upper tool part firmly and check the fit regularly. Set the spring strike as weak as possible and only as strong as necessary.
Size logic
- The tool size always corresponds directly to the resulting hole diameter.
- Therefore choose the same millimetre size as the hole you want to punch.
Available sizes
1.5 mm; 2 mm; 2.5 mm; 3 mm; 3.5 mm; 4 mm; 4.5 mm; 5 mm; 6 mm; 7 mm; 8 mm; 9 mm; 10 mm; 12 mm; 14 mm; 17 mmApplication in the press
- Screw the upper tool part fully into the press.
- Insert the lower brass anvil into the 12 mm holder.
- Place the material neatly and carry out the punching process with even pressure.
- Check the upper tool part regularly for a secure fit and retighten if needed.
Suitable materials
- The hole punch tool is intended for leather, faux leather, felt and cardboard.
- Smaller sizes are suitable for finer holes, larger sizes also for heavier material layers.
- No reliable approval for fabric is provided in this listing.
- Paper is not among the recommended material groups.
Usage notes
- The tool is intended for use with a press and not for hammer operation.
- For all Getmore Crafts hollow rivets and snap fasteners, a 2.5 mm hole punch tool is required.
- For eyelets, always choose the same size as the stated eyelet size or inner diameter.
- In the spring-strike press, the upper tool part should be tightened firmly with a suitable pair of pliers.
- Set the spring strike as weak as possible and only as strong as necessary.
With Getmore Crafts products
- Compatible with all Getmore Crafts presses with 1/4\" - 20 UNC upper thread and 12 mm holder at the bottom.
- For all Getmore Crafts hollow rivets and snap fasteners, a 2.5 mm hole punch tool is required.
- For Getmore Crafts eyelets, always choose the hole size to match the stated eyelet size or inner diameter.
- The brass anvil is part of the two-part hole punch tool.
With products from other manufacturers
- Usable only with presses that have 1/4\" - 20 UNC upper thread and a matching 12 mm holder.
- This listing is not suitable for presses with M6 or M8 thread. Separate hole punch tool variants are available for those.
Technical details
| Material | Upper tool part: alloy steel; lower tool part / anvil: brass |
| Surface treatment | Upper tool part nickel plated |
| Thread upper tool part | 1/4\" - 20 UNC |
| Length upper tool part | |
| Diameter lower tool part | 12 mm |
| Length lower tool part | |
| Available sizes | 1.5 mm; 2 mm; 2.5 mm; 3 mm; 3.5 mm; 4 mm; 4.5 mm; 5 mm; 6 mm; 7 mm; 8 mm; 9 mm; 10 mm; 12 mm; 14 mm; 17 mm |
| Tool construction | 2-part with upper tool part and lower brass anvil |
| Suitable materials | Leather, faux leather, felt, cardboard |
| Not recommended for | Paper |